Estimated local cost for house rewiring in Greensboro-High Point, NC, based on regional cost-of-living data. Updated April 2026.
Quick Answer: The estimated cost of house rewiring in Greensboro-High Point, NC is $3,650 – $13,700 ($3 – $8 per sq ft). Average: $7,750.Greensboro-High Point, NC is 9% below national average.
Source: ClearCost national data adjusted by BEA Regional Price Parity for Greensboro-High Point, NC — updated April 2026
Greensboro-High Point, NC
$7,750
Estimated range: $3,650 – $13,700
$3 – $8 per sq ft
National Average
$8,500
Range: $4,000 – $15,000
Greensboro-High Point, NC is 9% below national average based on BEA RPP data.
About these estimates: These prices are derived from our national pricing data adjusted for Greensboro-High Point, NC's cost of living (BEA Regional Price Parity: 91.3). Actual costs vary based on specific project requirements, contractor availability, and local material sourcing. See the national cost guide for full details.
Rewiring a house replaces outdated or unsafe wiring with modern copper wiring, updated outlets, and a new or upgraded electrical panel. Homes built before 1970 often contain knob-and-tube or aluminum wiring that poses fire risks and cannot support modern electrical loads. A full rewire for a typical 1,500–2,500 sq ft home costs $4,000–$15,000 nationally, depending on size, accessibility, and the extent of the work.
Home size is the primary cost driver for a full rewire. Larger homes require more wire, more circuits, more outlets, and more labor hours. The per-square-foot cost decreases slightly for larger homes because fixed costs like the panel upgrade, permits, and inspections are spread over more area. However, multi-story homes cost more per square foot than single-story ranch-style homes because wire runs between floors are more complex.
A full rewire involves several distinct components. New wiring throughout the home is the largest single expense, followed by the electrical panel upgrade. New outlets and switches are installed to meet current code spacing requirements, and all connections are brought up to modern grounding standards. The drywall repair needed to patch holes where wires were fished through walls can be a significant additional expense if walls need to be opened extensively.
Understanding the type of wiring in your home helps determine the urgency and scope of rewiring. Knob-and-tube wiring, found in homes built before 1940, uses ceramic knobs and tubes to route individual wires through framing — it lacks a ground wire and cannot safely handle modern loads. Aluminum wiring, common in homes built from 1965 to 1975, expands and contracts more than copper, creating loose connections that can overheat. Cloth-insulated wiring from the 1950s and 1960s becomes brittle and cracks over time, exposing bare conductors.
The accessibility of your home's wiring paths has a major impact on labor cost. In homes with unfinished basements and accessible attics, electricians can run new wires without opening many walls. In fully finished homes with no attic or basement access, walls must be opened to run new wiring, and the patching and painting afterward adds considerably to the total cost. Some electricians offer a partial rewire that replaces only the most critical circuits (kitchen, bathrooms, bedrooms) at a lower cost, leaving less-critical wiring in place.
$64,025
Labor is the single largest expense in a rewiring project, typically accounting for 60–70% of the total cost. A full rewire for a 2,000 sq ft home requires 50–80 labor hours spread over 5–10 working days. The work involves pulling new wire through walls, ceilings, and floors, installing new boxes and devices, connecting everything at the panel, and testing all circuits. At least two electricians typically work on a full rewire to keep the project on schedule.
A full house rewire takes 5–10 working days for a typical 1,500–2,500 sq ft home.
Common signs include frequently tripping breakers, flickering lights, discolored or warm outlets, burning smells, two-prong (ungrounded) outlets throughout the home, and a panel that still uses fuses. Homes built before 1970 with original wiring should be evaluated by a licensed electrician.
Yes. Many homeowners do a partial rewire, prioritizing the kitchen, bathrooms, and bedrooms first. This is particularly common during room-by-room renovations where walls are already open. However, the panel upgrade should be done upfront to support the new circuits.
Not usually. Power is typically disconnected for only a few hours at a time as the electrician works section by section. There will be noise and dust, but most families stay in the home during a rewire. If you have medical equipment that requires power, discuss a plan with your electrician.
Many insurance companies offer lower premiums after a rewire, especially if you are replacing knob-and-tube or aluminum wiring. Some insurers refuse to cover homes with these older wiring types or charge significant surcharges. A rewire certificate from a licensed electrician can qualify you for better rates.
ClearCost is expanding to Greensboro-High Point, NC
Get notified when our Fair Market Rate™ calculator and verified contractor matching launches in Greensboro-High Point, NC.